4 WAYS TO LACE SHOES

4 WAYS TO LACE SHOES

                     We all have been there, trying to lace up our shoes but being clueless. In this post you'll learn how to lace up your shoes nicely! So the next time when you buy a new shoe or want to lace up some other, this tip will come in handy for you :D.

STRAIGHT-LACE METHOD:

STEP 1:

           Place one end of the shoelace through the top right hole (the toe end) and the other end through the left hole on the bottom (near the beginning of the shoe). The left hole should have a short length of lace left; only enough to tie the lace at the end.

STEP 2:

              Using the right end, insert it in the opposite hole in a straight line.

STEP 3:

 

            Bring it out from the bottom, and insert it (from the bottom again) through the next hole.

STEP 4:

             Continue moving it horizontally across the holes until you reach the last hole.

STEP 5:

             Tie your two remaining ends in a bow (see below).

CRISS-CROSS METHOD:

STEP 1:

             Put a shoe in front of you with the toe facing away from you. Starting from the two frontmost opposite facing holes, insert each end of the shoelace from the inside. Make sure both sides of the remaining laces are equal.

STEP 2:

             Working in a diagonal direction, insert the right end of the shoelace into the next left hole (from the top). Alternate method: You can insert the lace pointing from the front of the shoe inward (instead of going from the inside pointing outward), to give a more neat appearance.

STEP 3:

            Insert the left end of the shoelace into the next right hole

STEP 4:

            Continue working your way down until you reach the ends.

STEP 5:

             Make a bow (as below).

HEEL-LOCKING METHOD:

STEP 1:

               Lace your shoes using the criss-cross method, stopping before the last hole.

STEP 2:

             Take the lace on one side, and put it into the hole on the same side. Do the same for the other lace.

STEP 3:

             Insert the left lace through the loop you have now created on the right.

STEP 4:

              Repeat the same for the other lace.

STEP 5:

             Tie your shoes as you would normally, and enjoy your slip-free heels!

LATTICE METHOD:

STEP 1:

             The lace is run straight across the bottom and the ends emerge through both bottom eyelets.

STEP 2:

            The ends are crossed over each other, run diagonally upwards on the outside and fed in through the third-higher set of eyelets up the shoe (skip past two sets of eyelets).

STEP 3:

            Both ends are run straight up the inside and emerge through the next set of eyelets up the shoe.

STEP 4:

             The ends are crossed over each other, run diagonally downwards on the outside and fed in through the third-lower set of eyelets down the shoe (skip past two sets of eyelets).

STEP 5:

                     Both ends are run straight up the inside and emerge through the next set of eyelets up the shoe.

STEP 6:

             The ends are crossed over each other, run diagonally upwards on the outside, then fed under the sides to emerge through the top set of eyelets (skip past two sets of eyelets).

TYING THE BOW:

STEP 1:

            Hold both ends of the lace straight. Place the right end over the left, then bring the left above the right and through the loop. Pull both ends tight.

STEP 2:

            Take hold of the right lace and form a loop, placing your finger in between to hold it. Bring the left lace over the right, and underneath it in a circular motion.

STEP 3:

             Then bring the left lace through the small loop. Pull tight.

STEP 4:

             Your shoes are now tied!

                        So, now that you have learnt this simple hack to tie shoe laces, share it with your Friends and ask them to share with others!

                     For more hacks, browse our website or search for a specific hack! :D.